程序運算英文

• program operation
• programmed algorithm
• sequential operation

• "程序" 英文翻譯 :    procedure
• "運算" 英文翻譯 :    operation; arithmetic; opera ...
• "源程序運算" 英文翻譯 :    source program operation
• "程序運算分析" 英文翻譯 :    program operation analysis
• "匯編程序運算符" 英文翻譯 :    a embler operator; assembler operator
• "例行程序操作子程序運算" 英文翻譯 :    routine operation
• "可編程序運算放大器" 英文翻譯 :    programmable mable operational amplifier; programmable operational amplifier
• "可編程序運算放大器電路" 英文翻譯 :    programable operational amplifier circuit
• "按序運算" 英文翻譯 :    sequential operation
• "順序運算符" 英文翻譯 :    sequential operator
• "程序運行" 英文翻譯 :    program execution; program running
• "逐程序運行" 英文翻譯 :    steover
• "子程序運行" 英文翻譯 :    subprogram activation
• "程序運行方式" 英文翻譯 :    program run mode
• "匯編程序運行" 英文翻譯 :    a embly run; assembly run
• "基準程序運行" 英文翻譯 :    benchmark run
• "監督程序運行" 英文翻譯 :    monitor run
• "程序運行的效率" 英文翻譯 :    vba
• "多道程序運行系統" 英文翻譯 :    multiprogramming operation system
• "符號調試程序運行" 英文翻譯 :    symbolic debugger operation
• "連接編輯程序運行" 英文翻譯 :    linkage editor run
• "目標程序運行時間" 英文翻譯 :    object program time
• "時序操作 順序操作 順序運算" 英文翻譯 :    sequentialoperation
• "運算程序" 英文翻譯 :    operating program; operational program; operational sequence; operator routine; production program
• "運算程序庫" 英文翻譯 :    algorithm library; arithmetic library

• The simulation program was complied under the real - time simulation support system , asca
  在實時仿真支撐系統asca下編寫了計算程序，通過改變程序運算速度達到實時的需要。
• Then , with comparing and analyzing , three examples are taken to verify the reliability of the calculation method and the result of program in this paper
  并且用三個算例對比分析來檢驗計算方法及程序運算結果的可靠性。
• Note 1 : don ' t make buildings too specialized in look ? it ' s a bit the same rule than ships , although more flexible -
  注意1 ：建造建筑物時不要過度追求視覺效果? ?建筑物的程序運算法則比飛船的運算法則來的簡單，雖然它有更大的靈活性。
• They will probably get instanced in cities and use special procedural algorithms ( ala gta ) to not require too much server bandwidth
  它們會出現于城市當中，我們會使用一些特別的程序運算方式（像gta那種） ，把服務器帶寬的要求降到最低。
• The result indicates that this program is safe and reliable for pdew fuzzy optimization . the researching in this paper has been obtained some worth in fuzzy optimization design and motions of pdew
  以某橡膠廠輪胎硫化機弧面蝸桿減速器為例，驗證了該模糊優化設計程序，結果表明該程序運算準確可靠，優化結果可行。
• How to make the design flow accord with actual situation needs inquiring into . this paper presents a simple calculation formula based on probability method with studying the hunter ' s method and russian method deeply
  本文采用概率方法，運用程序運算分別對美國亨特方法和俄羅斯現行規范采用的方法進行了深入探討，并在此基礎上提出了符合實際情、計算簡單方便查閱的計算公式。
• In order to view the results of computing in effect , the paper alse discusses the three dimension visualization . due to the opengl ' s ability and efficiency in 3 - d program , the paper discusses the theory of opengl in detailed , simultaneously discusses the programming process and realizing method
  為了能夠有效的顯示程序運算結果，論文還討論了三維顯示的問題，由于opengl技術在三維顯示上的有效性與靈活性，論文詳細討論了opengl技術原理與三維顯示實現的過程和方法。
• For better veracity of simulating model , model is used lookup - table module to calculate the thermodynamic character of refrigerant , and datas of experience and test is combined in the compressor module , also the coefficient of heat transfer changing by running parameter is decided by computational procedure . in addition , choosing congruence step size solves the divergence of simulation procedure
  為了使仿真模型具有相當的準確性，模型中采用查表模塊進行制冷劑熱力性質計算，壓縮機模塊中將實驗數據與經驗計算數據相結合，通過程序運算確定冷凝器和蒸發器傳熱系數與運行參數之間的關系，并成功解決了仿真程序運行發散的問題。
• At the same time adopting the single factor analytic approach , changing the rigidity and damping of fore - suspension and rear - suspension separately , using the simulation calculation procedures that are designed to carry on operational analysis , the optimization values of fore - suspension and rear - suspension parameters are gotten . compared the results that the simulation calculation procedures operated the optimization values with the simulation result before optimization , the effect is relatively good
  同時采用單因素分析法，分別改變前、后懸架的剛度和阻尼，利用所設計的程序進行運算分析，得到前、后懸架參數的優化值，并將所有優化后的參數值代入計算程序運算后得出的結果與優化前的模擬計算結果比較，發現優化后效果較好。
• Using the digital technology improves the performance traditional thyristor welding machine , according to the characters of the double inverse star from rectifier circuit , set the parameters with micro - controller accurately , design the dependable trigger circuit , lead the feedback of voltage for the operation program , so the voltage of main circuit be carried out very steadily
  摘要利用數字控制技術對傳統晶閘管焊接電源進行改進，根據雙反星型晶閘管整流電路的特點，采用單片機進行精確設定，設計了高可靠性觸發回路，結合電壓反饋進行程序運算控制，實現了主電路輸出電壓的精確調整和可靠運行。